INSTRUCTION MANUAL
FOR ASSEMBLY AND INSTALLATION OF
EF-L1000CG <METAL FIXTURES SUSPENDED FROM CEILING>
LCD Projector Compatible with Installation
Model Name: LX-D1000 (Body’s mass is 4.5 Kg)
For Selling and Installing Stores
■ Read this instruction manual carefully before assembly and/or installation. Be sure to carry out the
work properly always with safety in mind.
■ Do not permit the customers to engaged in assembly and/or installation. Make sure that your custom-
ers request you, the professional installers, for assembly and/or installation.
■ It is mandatory that you use the provided accessories for assembly and/or installation work. The metal
fixtures cannot be used for the LCD (liquid crystal display) projectors and appliances other than those
that are designated by our company.
■ The total mass of the metal mixtures for the ceiling is 5.5 Kg.
DETAILS TO BE STRICTLY O BSERVED FO R SAFETY
Before assembly and/or installation, be sure to read carefully the “details to be strictly observed for safety.”
The risk and its extent caused by erroneous handling are demarcated as follows:
Probability that can result in critical consequences such as death or serious injury in case of erroneous
WARNING
handling.
Probability that can result in injury or damage of houses and/or household effects in case of erroneous han-
CAUTION
dling.
WARNING
Carry out installation so that a safety rate definitely comes to
more than 5 times.
Be sure to carry out installation under a ceiling with a horizontal
surface.
Select a strong place where the mass of the LCD projector and
the metal fixtures can be held sufficiently.
Avoid installation under an inclined or warped ceiling.
If they are installed at a spot having insufficient strength, the
metal fixtures attached to the ceiling can come off and fall, re-
sulting in injury.
CAUTION
Take necessary measures to prevent any possible swing using
Pay attention not to allow any children hang onto the fixtures.
wires, etc.
Otherwise, injury can result.
Otherwise, temblors and vibrations can result in falls, causing
injury.
Be sure to install them at a place where there is no other appa-
ratus such as a fire alarm, etc., or malfunction of appliances and
instruments, etc., can result.
BHU30002-036-001
– 1 –
Fig . 3 ASSEMBLY
y Ceiling plate
! Washers (for M10)
! 2 rotary mini
setscrews (M5 × 5)
20
Fig . 3 -1
10
! Nut
t 2 screws [A]
(M4 × 12)
! Hexagon head bolts
[C] (M10 × 65)
u Inner pole
! 4 hexagon socket
q Coupling
! Washer (for M10)
plate
! Collar
bolts (M5 × 16)
(109.6)
150
i Inner pole
fixing plate
Size of fixing hole of base metal fixtures
@ 4 nuts (for M5)
r 2 rotary setscrews [E] (M5 × 10)
! 4 washers
(for M5)
e 4 assembling bolts (M8 × 25)
o 4 hexagon socket
bolts (M5 × 10)
! Hexagon wrench
(accessory)
Body’s plate
(*) Fastening bolts for
body’s plate (4 bolts)
(*) Holder plates (2 plates)
Air inlet (❈)
Hexagon socket bolts
for M5
LCD projector
(*) Fastening bolts for
holder plate (8 bolts)
! 2 screws [B] (M8 × 14)
Note:
w Supporter for LCD projector
❈ Air inlet:
This is an inlet to bring cool air into the LCD
projector. Do not cover it with a lid, etc.
Unit of indicated dimensions (mm)
WARNING
(*) Parts
: The asterisked parts such as the holder plates (2 plates), fastening bolts for holder plates (8 bolts), and fastening bolts for body’s
plate (4 bolts) are built in to constitute component parts of the body’s plate.
: Never remove the above-mentioned component parts under any circumstances since they are absolutely required to ensure safety.
Fig . 4 FRO N T VIEW
Exhaust hole (❈)
Note:
24
❈ Exhaust hole:
This is a hole to exhaust hot air inside the LCD projector. When
installing the unit near a wall, etc., keep it away more than 50 cm
or so from the face of the exhaust hole.
Unit of indicated dimension (mm)
– 3 –
ADJUSTMEN T O F PRO JECTIO N PO SITIO N
(Refer to Fig. 5)
Carry out horizontal and vertical adjustments as follows:
1.
(1) To adjust the horizontal position of the screen, loosen rotary setscrews [E] (there are two pieces on both sides) and 4 hexagon
socket bolts (M5 × 10), and rotate the projector horizontally.
(2) To adjust the vertical position of the screen, loosen the assembling bolts (there are 4 pieces on both sides), then tilt the front of the
projector vertically.
Tighten the rotary setscrews [E], hexagon socket bolts (M5 × 10), assembling bolts, and fix the LCD projector.
2.
Fig . 5 ADJUSTMEN T
Hexagon wrench
(accessory)
Rotary setscrew [E]
Assembling bolt for M8
Assembling bolt
(M8 × 25)
Tip of LCD Projector ~ Center of ceiling plate
148
Lens center
Tilt adjusting latitude
of 15 degrees
339
367
Unit of indicated dimensions (mm)
FILTER CLEAN IN G
(Carry out filter cleaning with appropriate intervals)
Before replacing the filter, never forget to turn
OFF the main power switch and unplug the
power cord from the outlet.
Fig . 6 REPLACEMEN T
Remove the 2 filter guard fixing screws,
and remove the filter guard.
1.
Filter guard
Filter
Filter cover
Push the knob of the filter cover in the
2.
direction indicated by the arrow mark, and
raise it.
Take out the filter, wash it well in water or
3.
2 filter guard
fixing screws
synthetic detergent, and dry it completely.
Set the filter on the filter cover, and install
the filter cover on the body.
4.
Tighten 2 filter guard fixing screws, then
5.
set the filter guard.
Printed in Japan
0999YMPS/VP
VICTOR COMPANY OF JAPAN, LIMITED
– 4 –
|
Indesit Dishwasher D41 User Manual
Insignia Computer Drive NS PCH5421 User Manual
JBL Speaker P81 User Manual
Jensen Popcorn Poppers KT5230 User Manual
JVC DVD Player CU VH1 User Manual
JVC Flat Panel Television AV 28X4BU User Manual
Jwin MP3 Player JX CD910 User Manual
Kenwood Car Video System KDC MP342U User Manual
KitchenAid Range KDRP707R User Manual
Kolcraft Stroller S64 R2 User Manual